Canton oil pan/windage tray installed

[03 cobra toy]

Hard core OT people you should think about installing this oil pan....It's the same pan Ford installed on the 00R. It holds 9.5qts of oil. :thumbsup:

[03 cobra toy]

2pic

[Firme]

:drool:

how much $$ ???.... me likey



woah....did you install a Windage tray also?

[03 cobra toy]

pic3

[03 cobra toy]

Originally posted by Firme
:drool:

how much $$ ???.... me likey



woah....did you install a Windage tray also?
Yes see pic...

$340+2 Hours to install

[Levi]

That is awesome and it looks cool too..............:thumbsup:

[97CasperCobra]

Better be careful at TWS with that, see what Joe did??
"Joe ended up cutting his day short when he developed a leak in his oil pan late in the day. He apparently was bottoming out coming into 1 alot and it shaved down the lip on the back side of the pan.. and it developed a leak."

Just wanted to give ya a heads up. Looks good man. :thumbsup:

[Firme]

From what I remember Andy saying, I think Joes car was REALLY REALLY low to the ground....

I wanna say he has the Steeda X2 balljoints which drop the front 1/2" but didn't use their kit that raises it back up 1/2"....


don't quote me on that though, I'm sure Andy or Joe can correct me here...

[cobrapace94]

Looks good David... :thumbsup: :bounce:
Probly work good for drag racing also. :thumbsup:

And Davids car is not slammed??

[Firme]

Originally posted by cobrapace94
And Davids car is not slammed??

thats the beauty of coil-overs...one can heed the warnings, learn from others, and avoid slamming the car down on turn 1A by adjusting them :thumbsup:, a luxury conventional spring don't offer :D :bounce:

[03 cobra toy]

Originally posted by 97CasperCobra
Better be careful at TWS with that, see what Joe did??
"Joe ended up cutting his day short when he developed a leak in his oil pan late in the day. He apparently was bottoming out coming into 1 alot and it shaved down the lip on the back side of the pan.. and it developed a leak."

Just wanted to give ya a heads up. Looks good man. :thumbsup:

The 00R motor sits lower than the 03 ;) My oil pan sits even with the k-member and I think my k-member brace would be the first thing to go...See pic :thumbsup:

[Firme]

Originally posted by 03 cobra toy
The 00R motor sits lower than the 03 ;) My oil pan sits even with the k-member and I think my k-member brace would be the first thing to go...See pic :thumbsup:

damn dude... http://www.svtmustangcobraclub.com/imgs/smilies/poke.gifyour under-cariage is filthy,http://www.svtmustangcobraclub.com/imgs/smilies/nonono.gif you need to paint your cats....


http://www.svtmustangcobraclub.com/imgs/smilies/biggrinjester.gif

[03 cobra toy]

Originally posted by Firme
damn dude... http://www.svtmustangcobraclub.com/imgs/smilies/poke.gifyour under-cariage is filthy,http://www.svtmustangcobraclub.com/imgs/smilies/nonono.gif you need to paint your cats....


http://www.svtmustangcobraclub.com/imgs/smilies/biggrinjester.gif


:321: :fart:

[Andy M]

David,

Cool man!!!

See you guys in a couple of weeks at MSR!!

[Topless In Tex]

DAMN DAVID..
Just when I think your Cobra cant look any better you go doing **** like that.....and If I've said it once, I will say it again, Your COBRA is #1 in my book :hail: Your Stang gives WhiteSnake a run for the money! ;) (keeping in mind those miles..but you are THERE!) :D
....I've judged it now 2 or 3 times, and I always save it for last....cuz I know how awesome it is. Its a PLEASURE to see someone take such pride in thier Stang.....:thumbsup:
You should be proud. It just keeps getting better!!!!!!! :hail:
:banana:TNT:banana:

and...it blows my mind that you are getting into racing it, and the undercarriage looks THAT CLEAN!!!!!!!!! I'm in AWE!!!! :hail: And, I know you will keep it up! YOU SHOULD HAVE DONE AUTORAMA THIS YEAR!!!!!!:cool:

[03 cobra toy]

Originally posted by Topless In Tex
DAMN DAVID..
YOU SHOULD HAVE DONE AUTORAMA THIS YEAR!!!!!!:cool:

Next year ;) (F*** off Edmond don't even say it) After the Kenny Bell :D

[Firme]

http://www.svtmustangcobraclub.com/imgs/smilies/biggrinjester.gif

[97CasperCobra]

Originally posted by Firme
woah....did you install a Windage tray also?

what's a windage tray?? :retard:

[Twice Bitten]

It captures the wind and serves it to you inside the car to keep you refreshed will on the open track :D :D :grinangel :grinangel :grinangel :grinangel

[03 cobra toy]

Originally posted by 97CasperCobra
what's a windage tray?? :retard:


It helps keep the oil in the pan and away from the crankshaft...

[Firme]

Originally posted by 03 cobra toy
It helps keep the oil in the pan and away from the crankshaft...

Werd

without one, the crank lobes get oil all over them (more than needed) and it adds to the rotating mass of the crank... thus robbing power

[97CasperCobra]

bout how much one of them darn thingys cost??

[venomous]

Dang, I bet an oil change for one of them there thingys would be a little more expensive than a regular one....wouldn't you think???;) It looks awesome though. Might just save some money and put one on mine!!:thumbsup:

[Big Daddy]

Originally posted by venomous
Dang, I bet an oil change for one of them there thingys would be a little more expensive than a regular one....wouldn't you think???;) It looks awesome though. Might just save some money and put one on mine!!:thumbsup:

I have the same oil pan on my '01 and I also have an oil cooling system and my Vortech uses the oil from the oil pan during operation. It took 10 quarts to fill it up the last time! AND YES IT'S MORE EXPENSIVE! :D ;)

[Carl G]

Got the Canton in at Nathanials, the only thing we are concerned about is how it will fit with the headers and exhaust. Hope it works like the extra insurance.

[03 cobra toy]

Originally posted by Big Daddy
I have the same oil pan on my '01 and I also have an oil cooling system and my Vortech uses the oil from the oil pan during operation. It took 10 quarts to fill it up the last time! AND YES IT'S MORE EXPENSIVE! :D ;)

10.5 quarts for me @ $7.80 a qt... $100 oil change :(

Carl,

It will fit with header.... no problem :D Make sure they install the windage tray also!!!


Mike,

Cost for the pan and W tray is about $360

[93KingCobra]

Not a bad price for the insurance it give's you. I know I would not want to blow an 03 motor. Looks real good:thumbsup:

[venomous]

Originally posted by 03 cobra toy
10.5 quarts for me @ $7.80 a qt... $100 oil change :(

Carl,

It will fit with header.... no problem :D Make sure they install the windage tray also!!!


Mike,

Cost for the pan and W tray is about $360
$100 dollars for an oil change!!!!! :eek: :eek: :eek: God Bless, thats a pretty penny just for an oil change. OMG!!!:eek:

[Carl G]

Originally posted by Firme
:drool:

how much $$ ???.... me likey



woah....did you install a Windage tray also?

Got the Canton at Nathanials looks good. You can run your Oil temp guage straight from the pan. Also I have been told that the 03 have a windage tray which can be used in the Canton. Any comments on this.

[03 cobra toy]

Originally posted by Carl G
Also I have been told that the 03 have a windage tray which can be used in the Canton. Any comments on this.

:( I didn't see one....There is an oil deflector for the crank that is welded to the pickup tube maybe they think that's the windage tray?? I think the cost for one is about $50+another oil pan gasket... See pic

[Bingo13]

Originally posted by Carl G
Got the Canton at Nathanials looks good. You can run your Oil temp guage straight from the pan. Also I have been told that the 03 have a windage tray which can be used in the Canton. Any comments on this.

Steve at HP told me they will be adding the windage tray from the stocker on my Canton install next week.

[03 cobra toy]

Originally posted by Bingo13
Steve at HP told me they will be adding the windage tray from the stocker on my Canton install next week.

I don't understand??? I didn't see any windage tray on the stock oil pan...

[Carl G]

Maybe it got left off from the factory? :D

[Bingo13]

Originally posted by 03 cobra toy
I don't understand??? I didn't see any windage tray on the stock oil pan...

I have no idea but will keep my eyes open during the install. I bought your oil cooler items also. :thumbsup:

[03 cobra toy]

Originally posted by Bingo13
I have no idea but will keep my eyes open during the install. I bought your oil cooler items also. :thumbsup:

Let me know if you need any help with the cooler :thumbsup: